SOtM docs

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
en:how_to_use_wifi_in_eunhasu [2017/01/06 03:58] – created sanghoonen:how_to_use_wifi_in_eunhasu [2023/10/04 21:44] (current) – [Requirement] admin
Line 1: Line 1:
 ====== Requirement ====== ====== Requirement ======
-  * sMS-200 V0.3.0 or sMS-1000SQ Eunhasu V0.3.0 + 
-  * Wifi dongle +  * sMS-200 V0.3.0 above or sMS-1000SQ Eunhasu V0.3.0 above 
-    * RTL8812AU chipset+  * Wifi dongle 
 +      a Wifi dongle which uses a RTL8811AU, RTL8812AU, RTL8812A, RTL8821A or RTL8814A, RTL88x2BU, RTL8821AU, RTL8821CU, RTL8814AU chipset.
  
 ====== Simple Instruction ====== ====== Simple Instruction ======
-Connect Wifi USB dongle into USB port. 
-{{ :en:media-20170106.jpg |}} 
  
-Click 'Wifi' tab in System config page. +Connect a Wifi USB dongle into on of the two USB port. To setup Wifi feature on Eunhasu, the wired LAN should be connected.{{  :en:media-20170106.jpg  }} 
-{{ :en:2017-01-06_17.16.54-fullpage.png |}}+ 
 +Click 'Wifi' tab in System config page. {{  :en:2017-01-06_17.16.54-fullpage.png  }} 
 + 
 +Click 'Wifi Router' button to show Wireless Access Point and it will take a few minutes to be detected the AP.{{  :en:2017-01-06_17.17.15-fullpage.png  }} 
 + 
 +Select AP what you want. {{  :en:2017-01-06_17.17.42-fullpage.png  }} 
 + 
 +Enter password or secret if required. {{  :en:2017-01-06_17.17.50-fullpage.png  }} 
 + 
 +Wait till the progress will be done.{{  :en:2017-01-06_17.17.55-fullpage.png  }} 
 + 
 +After connecting successfully, you can see IP address like the screen shot below. {{  :en:2017-01-06_17.17.59-fullpage.png  }} 
 + 
 +If you need to remove the Wifi connection information, Click 'Remove Wifi Information' button, it will remove all saved information including the name and password. {{  :en:2017-01-06_17.17.59-fullpage2.png  }} 
 + 
 +<note important> 
 + 
 +  * Eunhasu version >= V0.3.0 is required. 
 +  * There might be connection error if you use wired and wireless network at the same time. 
 +  * Network speed could be degraded depends on wireless network status. 
 +  * After connected wireless, use the IP address to be connected. 
 + 
 +</note> 
 + 
 +====== Reference ====== 
 +===== Video clip ===== 
 +{{ youtube>wG9bUV2-XHw }}
  
-Click 'Wifi Router' button to show Wireless Access Point. +===== Device IDs in driver =====
-{{ :en:2017-01-06 17.17.15-fullpage.png |}}+
  
-Select AP what you want. +  * 0x050D, 0x1106 : Belkin - sercomm 
-{{ :en:2017-01-06 17.17.42-fullpage.png |}}+  * 0x050D, 0x1109 Belkin F9L1109 - SerComm 
 +  * 0x2001, 0x330E D-Link ALPHA 
 +  * 0x7392, 0xA822 : Edimax Edimax 
 +  * 0x0DF6, 0x0074 : Sitecom - Edimax 
 +  * 0x04BB, 0x0952 : I-O DATA - Edimax 
 +  * 0x0789, 0x016E : Logitec - Edimax 
 +  * 0x0409, 0x0408 : NEC - 
 +  * 0x0B05, 0x17D2 : ASUS - Edimax 
 +  * 0x0E66, 0x0022 : HAWKING - Edimax 
 +  * 0x0586, 0x3426 : ZyXEL - 
 +  * 0x2001, 0x3313 : D-Link - ALPHA 
 +  * 0x1058, 0x0632 : WD - Cybertan*/ 
 +  * 0x13B1, 0x003F : Linksys WUSB6300 
 +  * 0x1740, 0x0100 : EnGenius - EnGenius 
 +  * 0x2019, 0xAB30 : Planex - Abocom 
 +  * 0x07B8, 0x8812 : Abocom - Abocom 
 +  * 0x2001, 0x3315 : D-Link - Cameo 
 +  * 0x2001, 0x3316 : D-Link - Cameo 
 +  * 0x20F4, 0x805B : TRENDnet - Cameo 
 +  * 0x2357, 0x0101 : TP-Link - Archer T4U 
 +  * 0x2357, 0x0103 : TP-Link - T4UH 
 +  * 0x2357, 0x010D : TP-Link - Archer T4U AC1300 
 +  * 0x2357, 0x010F : TP-Link - Archer T4UHP 
 +  * 0x148F, 0x9097 : Amped Wireless ACA1
  
-Enter password or secret if it required. +----
-{{ :en:2017-01-06 17.17.50-fullpage.png |}}+
  
-Waiting for seconds. +Last Updated~~LASTMOD~~
-{{ :en:2017-01-06 17.17.55-fullpage.png |}}+
  
-After connect successfully, you can see IP address like screen shot. 
-{{ :en:2017-01-06 17.17.59-fullpage.png |}} 
  
-'Remove Wifi Information' button will remove all stored information include name and password. 
-{{ :en:2017-01-06 17.17.59-fullpage2.png |}}