SOtM docs

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
en:how_to_enable_gigabit_ethernet_in_sms-200 [2017/01/12 03:07] – [Preparation] sanghoonen:how_to_enable_gigabit_ethernet_in_sms-200 [2020/01/07 16:09] (current) – [Remove 'C670' Chip Capacitor] admin
Line 5: Line 5:
 ===== Disassemble the front case ===== ===== Disassemble the front case =====
  
-Unscrew 4 points of Torx screws as like the image below. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw1.png  }}+Unscrew the 4 Torx screws as shown. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw1.png  }}
  
 ===== Disassemble the LED board ===== ===== Disassemble the LED board =====
Line 13: Line 13:
 ===== Disassemble the rear case ===== ===== Disassemble the rear case =====
  
-Unscrew 4 points of Torx screws as like the image below. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw3.png  }}+Unscrew the 4 Torx screws as shown. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw3.png  }}
  
 ===== Remove 'C670' Chip Capacitor ===== ===== Remove 'C670' Chip Capacitor =====
  
-Pull out the rear case very carefully to disassemble the main board from the body case. Remove 'C670' by a soldering machine. If required, the power board can be disassembled. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw4.jpg  }}+Pull out the rear case very carefully to disassemble the main board from the body case. Remove 'C670' with a soldering iron. If necessary, the power board can be disassembled. {{  :en:how_to_enable_gigabit_ethernet_in_sms-200_hw4.jpg  }}
  
 ===== Assemble sMS-200 cases ===== ===== Assemble sMS-200 cases =====
Line 25: Line 25:
 ====== Software ====== ====== Software ======
  
-Change the micro SD card image+To change the micro SD card image, please refer to [[en:eunhasu:burn_sdcard_image|'burn sdcard image']] page.
  
 ===== Windows ===== ===== Windows =====
Line 56: Line 56:
  
 ===== macOS ===== ===== macOS =====
-<note warning>**testing now. not verified manner**</note>+
  
 ==== Preparation ==== ==== Preparation ====
Line 64: Line 64:
   - Eject the micro SD card from the rear case of sMS-200 and insert to PC USB port by using the micro SD card reader.   - Eject the micro SD card from the rear case of sMS-200 and insert to PC USB port by using the micro SD card reader.
  
-==== Select File to Restore==== 
-{{ :en:capture_20170111104820.png |}} 
  
 ==== Start Restore==== ==== Start Restore====
Line 81: Line 79:
  
 After done, insert the SD card to sMS-200 rear. After done, insert the SD card to sMS-200 rear.
 +
 +You can also use command-line by terminal instead of dd utility. Refer to [[https://www.cyberciti.biz/faq/how-to-create-disk-image-on-mac-os-x-with-dd-command/|here]].