====== Requirement ======

  * sMS-200 V0.3.0 above or sMS-1000SQ Eunhasu V0.3.0 above
  * a Wifi dongle
      * a Wifi dongle which uses a RTL8811AU, RTL8812AU, RTL8812A, RTL8821A or RTL8814A, RTL88x2BU, RTL8821AU, RTL8821CU, RTL8814AU chipset.

====== Simple Instruction ======

Connect a Wifi USB dongle into on of the two USB port. To setup Wifi feature on Eunhasu, the wired LAN should be connected.{{  :en:media-20170106.jpg  }}

Click 'Wifi' tab in System config page. {{  :en:2017-01-06_17.16.54-fullpage.png  }}

Click 'Wifi Router' button to show Wireless Access Point and it will take a few minutes to be detected the AP.{{  :en:2017-01-06_17.17.15-fullpage.png  }}

Select AP what you want. {{  :en:2017-01-06_17.17.42-fullpage.png  }}

Enter password or secret if required. {{  :en:2017-01-06_17.17.50-fullpage.png  }}

Wait till the progress will be done.{{  :en:2017-01-06_17.17.55-fullpage.png  }}

After connecting successfully, you can see IP address like the screen shot below. {{  :en:2017-01-06_17.17.59-fullpage.png  }}

If you need to remove the Wifi connection information, Click 'Remove Wifi Information' button, it will remove all saved information including the name and password. {{  :en:2017-01-06_17.17.59-fullpage2.png  }}

<note important>

  * Eunhasu version >= V0.3.0 is required.
  * There might be connection error if you use wired and wireless network at the same time.
  * Network speed could be degraded depends on wireless network status.
  * After connected wireless, use the IP address to be connected.

</note>

====== Reference ======
===== Video clip =====
{{ youtube>wG9bUV2-XHw }}

===== Device IDs in driver =====

  * 0x050D, 0x1106 : Belkin - sercomm
  * 0x050D, 0x1109 : Belkin F9L1109 - SerComm
  * 0x2001, 0x330E : D-Link - ALPHA
  * 0x7392, 0xA822 : Edimax - Edimax
  * 0x0DF6, 0x0074 : Sitecom - Edimax
  * 0x04BB, 0x0952 : I-O DATA - Edimax
  * 0x0789, 0x016E : Logitec - Edimax
  * 0x0409, 0x0408 : NEC -
  * 0x0B05, 0x17D2 : ASUS - Edimax
  * 0x0E66, 0x0022 : HAWKING - Edimax
  * 0x0586, 0x3426 : ZyXEL -
  * 0x2001, 0x3313 : D-Link - ALPHA
  * 0x1058, 0x0632 : WD - Cybertan*/
  * 0x13B1, 0x003F : Linksys WUSB6300
  * 0x1740, 0x0100 : EnGenius - EnGenius
  * 0x2019, 0xAB30 : Planex - Abocom
  * 0x07B8, 0x8812 : Abocom - Abocom
  * 0x2001, 0x3315 : D-Link - Cameo
  * 0x2001, 0x3316 : D-Link - Cameo
  * 0x20F4, 0x805B : TRENDnet - Cameo
  * 0x2357, 0x0101 : TP-Link - Archer T4U
  * 0x2357, 0x0103 : TP-Link - T4UH
  * 0x2357, 0x010D : TP-Link - Archer T4U AC1300
  * 0x2357, 0x010F : TP-Link - Archer T4UHP
  * 0x148F, 0x9097 : Amped Wireless ACA1

----

Last Updated: ~~LASTMOD~~